The Adventure Begins- My 620 build thread

320 through 720
dat521
Posts: 161
Joined: Sun May 26, 2019 11:53 pm
Location: laveen

Re: The Adventure Begins- My 620 build thread

Post by dat521 »

looking good
User avatar
Randalla
Posts: 930
Joined: Fri May 24, 2019 8:58 am
Location: North Scottsdale

Re: The Adventure Begins- My 620 build thread

Post by Randalla »

Yes, Stephen, I now have the cowl re-installed.

Today I finished bolting on the front shocks and new stabilizer bar end links. In the process, I evaluated the front disc brakes. I'm constantly amazed at the crazy stuff people do, jerry rigging things (potentially dangerously), rather than just replacing with the correct parts. Today I found one of the slider pins on the driver's side brake caliper substituted with what looks to be some type of construction fastener and piece of wire wrapped around it to hold it in place, Arghhhhh! Also noticed the inside pad on both driver and passenger sides was nearly gone, while the outside pad still had over 50% life left. Picked up new pads and hardware kit at O'Reilly this afternoon. Both rotors look like they'll need replacing as well. Since this 1977 truck did not come from the factory with front disc brakes, I was unsure if they were Datsun 620 or something else. After matching the pads up, it appears at some point the brakes were upgraded with 1978 or 79 620 parts.
Attachments
IMG_8634.jpg
IMG_8630.jpg
IMG_8628.jpg
1967 1/2 Roadster- 1600 4 cyl.
1972 240Z- 280 I-6
1976 710 Wagon- L20B 4 cyl.
1977 620 King Cab - L18 4 cyl.
2003 350Z Track- VQ V-6
User avatar
Randalla
Posts: 930
Joined: Fri May 24, 2019 8:58 am
Location: North Scottsdale

Re: The Adventure Begins- My 620 build thread

Post by Randalla »

Got new front brake pads and hardware installed today as well as my Lokar accelerator cable. Despite looking pretty nasty, I was able to get all the front brake lines loose without rounding the corners of the fittings. Still need to order and replace both front rotors. I know I did this backwards, but all the cleaning is now behind me and it will be really quick to swap out the rotors when they arrive. Been keeping track of all my expenses and at this point I'm still under $5,000, all in. Definitely a budget build.
Attachments
IMG_8638.jpg
IMG_8639.jpg
1967 1/2 Roadster- 1600 4 cyl.
1972 240Z- 280 I-6
1976 710 Wagon- L20B 4 cyl.
1977 620 King Cab - L18 4 cyl.
2003 350Z Track- VQ V-6
User avatar
Randalla
Posts: 930
Joined: Fri May 24, 2019 8:58 am
Location: North Scottsdale

Re: The Adventure Begins- My 620 build thread

Post by Randalla »

Last Saturday I got bit bad by my grinder, and today ended up at a hand surgeon to assess the damage. Fortunately I was lucky, no surgery and everything is intact, though still pretty painful. Slowed me down for a few days, but hard back at it today after hearing my doctor's assessment. I'm waiting on a pair of front brake discs, which I expect to arrive tomorrow, so I've been working on a few cosmetic issues. The tailgate is pretty rough and had multiple layers of paint on it over the butterscotch. I've been slowly working on removing the white and gray paint to get to the original paint, while still preserving the " 5-Speed" and "Have a Nice Day" vinyl appliques. Keep in mind this is a budget build. My intent is to make this a "work truck tribute", so the flaws just add to the truck's and the original owner's history. I'm really starting to embrace and have fun with this concept, and even tried reaching the original owners son this evening to get some history, hear his recollections, and share what I'm doing.
Attachments
IMG_8647.jpg
IMG_8646.jpg
IMG_8640.jpg
1967 1/2 Roadster- 1600 4 cyl.
1972 240Z- 280 I-6
1976 710 Wagon- L20B 4 cyl.
1977 620 King Cab - L18 4 cyl.
2003 350Z Track- VQ V-6
User avatar
Duffman
Posts: 169
Joined: Sat May 25, 2019 10:52 am
Location: Scottsdale, AZ

Re: The Adventure Begins- My 620 build thread

Post by Duffman »

Ouch, Randy, looks painful! Tailgate looking good!
Duffman
1970 240Z, #1399
User avatar
L320-Dale
Posts: 340
Joined: Thu May 23, 2019 6:25 pm
Location: North Gilbert

Re: The Adventure Begins- My 620 build thread

Post by L320-Dale »

OUCH! That looks like it hurt a bit. Be careful buddy, don't want to see anymore missing skin. The 620 is coming along nicely.

Dale
Dale - Gilbert, Az
1965 L320 - Bamboo Tan / 1972 1200 - Sun-light Blue / 1970 240Z - Silver
User avatar
Randalla
Posts: 930
Joined: Fri May 24, 2019 8:58 am
Location: North Scottsdale

Re: The Adventure Begins- My 620 build thread

Post by Randalla »

Today was a banner day, of sorts. Got things back together enough to be able to fire the the motor with the new carb on starting fluid. The real test will be getting it to idle off tank gas, which I plan to do this weekend. My front brake rotors arrived and they will go on tomorrow, completing the front brake re-build. I was also able to test a few electrical accessories, finding the headlights, dash lights, and under hood light all work. However, I did remove the fuse block for some much needed cleaning with a brass gun barrel brush in my drill motor. It worked really well to remove the oxidation on the contacts. I'll be able to further test the electrical system tomorrow after re-installing the fuse block. Ron Q helped weld a much needed bracket back together, which had broken while removing it (thanks Ron!). I also refinished the taillight housings in preparation for the new lights I ordered and reinstalled the re-finished tailgate latch handles. Tonight I was able to remove the steering wheel with a puller to assess if it's salvageable.
1967 1/2 Roadster- 1600 4 cyl.
1972 240Z- 280 I-6
1976 710 Wagon- L20B 4 cyl.
1977 620 King Cab - L18 4 cyl.
2003 350Z Track- VQ V-6
User avatar
Randalla
Posts: 930
Joined: Fri May 24, 2019 8:58 am
Location: North Scottsdale

Re: The Adventure Begins- My 620 build thread

Post by Randalla »

Finished replacing the front rotors this morning and one wheel stud that had been broken at some time in the past. Thanks to Carl and Peter for the tool loan, as I never would have been able to get the floating brake calipers off otherwise. That completes the front brake system. Now on to the rear brakes and rebuilding the emergency brake. The clock is ticking and I'm beginning to wonder if I'll have it done to drive to the Williams show October1st. :?:
Attachments
IMG_8649.jpg
1967 1/2 Roadster- 1600 4 cyl.
1972 240Z- 280 I-6
1976 710 Wagon- L20B 4 cyl.
1977 620 King Cab - L18 4 cyl.
2003 350Z Track- VQ V-6
User avatar
Randalla
Posts: 930
Joined: Fri May 24, 2019 8:58 am
Location: North Scottsdale

Re: The Adventure Begins- My 620 build thread

Post by Randalla »

During the course of working on this truck I've been contemplating a vision for it. My guiding principals so far have been to:

1. Preserve or refresh everything I possibly can.
2. Do everything myself, learning new skills in the process
3. Make it safe and dependable
4. Make decisions with budget as a main priority
5. Remain true to its heritage as a working truck
6. Be creative and have fun

I'm hoping the paragraph below articulates my vision and what I'd ultimately hope to to achieve. I'd be interested in input from others. Thanks!


“Working Trucks”

In past times pickup trucks were primarily purchased to accomplish a job, not cherish, like much-loved automobiles. It would be fitting if there were a collector class for “working trucks”… restored mechanically, but testifying cosmetically to their heritage. There's beauty and strength of character in the scars these trucks acquired and carry today. They share characteristics similar to weathered, porcelain signs displayed on old barns and abandoned filling stations. Both share rich histories, retaining their preserved experiences, weathering, and wounds. Like vintage porcelain signs, working trucks were often artfully painted with the business owner's logo, name and contact information. I submit that “working trucks” be viewed as part of our transportation history, and curated accordingly. I'd place this class of trucks squarely between “Rat Rods” and “Survivors.”

Thoughts???

Just found this 620 for sale. Looks like its owner may have had a similar vision for his truck (check out the company name on the doors).
Attachments
d3b4016510604a7caec2132bd59ba599.jpg
d3b4016510604a7caec2132bd59ba599.jpg (18.42 KiB) Viewed 639 times
a43bc00a449d4554a272ddeafd8e02b7.jpg
a43bc00a449d4554a272ddeafd8e02b7.jpg (22.62 KiB) Viewed 639 times
683583686aa548a0a20e4d8f0e2ef3ad.jpg
73b67cc37bfb4d2abb747aa6f141881c.jpg
1967 1/2 Roadster- 1600 4 cyl.
1972 240Z- 280 I-6
1976 710 Wagon- L20B 4 cyl.
1977 620 King Cab - L18 4 cyl.
2003 350Z Track- VQ V-6
theAngryMarmot
Posts: 105
Joined: Sat May 25, 2019 9:10 pm

Re: The Adventure Begins- My 620 build thread

Post by theAngryMarmot »

As much as I love "showroom fresh" and perfectly finished vehicles - there is always something to be said about real wear and tear on a vehicle.

"Personalty" is a product of something's history and that is only created with real patina, wear & tear and sometimes abuse can create as it adds a backstory and life to the automobile.
Post Reply